Ultrasonik ndt ekipmanları Ultrasonik Muayene Ekipmanları Prob Dönüştürücü Fazlı Dizi Prob
1. Düz prob: tek kristal p-dalga düz prob çift kristal p-dalga düz prob
2. Açı probu: tek kristal kesme Açı probu a1 <aL <a Ⅱ, ikiz kesme Açı probu
Tek kristal p dalga eğik prob aL
AL is a climbing wave probe near a1. AL, a1 yakınlarındaki bir tırmanma dalgası probudur. The longitudinal wave transmitted along the surface of the workpiece has the advantages of fast speed, high energy, long wavelength, deeper detection depth than the surface wave, and the requirement for the surface finish of the workpiece is higher than that of the surface wave (frequency 2.5mhz wavelength about 2.4mm). İş parçasının yüzeyi boyunca iletilen uzunlamasına dalga, hızlı hız, yüksek enerji, uzun dalga boyu, yüzey dalgasından daha derin algılama derinliği avantajlarına sahiptir ve iş parçasının yüzey bitirme gereksinimi, yüzey dalgasından daha yüksektir ( frekans 2.5 mhz dalga boyu yaklaşık 2.4mm).
3. Eğrilikli prob: çevresel eğrilik, radyal eğrilik.
The circumferential curvature probe is suitable for the detection of axial defects in seamless steel tubes, straight welded tubes, tubular forgings and axial workpieces. Çevresel eğrilik probu, dikişsiz çelik borular, düz kaynaklı borular, boru biçimli dövmeler ve eksenel iş parçalarındaki eksenel kusurların tespiti için uygundur. When the diameter of the workpiece is less than 2000mm, the circumferential curvature of the probe shall be ground to ensure good coupling. İş parçasının çapı 2000 mm'den az olduğunda, iyi bir bağlantı sağlamak için probun çevresel eğriliği topraklanmalıdır.
Radyal eğrilik probu dikişsiz çelik borudaki radyal kusurların tespiti için uygundur, çelik borunun alın kaynağı, namlu dövme, şaft iş parçası, vb. iyi bağlantı.
4. Odaklama probu: nokta odaklama hattı odaklama.
5. Yüzey dalgası probu: (boyuna dalganın gelen Açısı ikinci kritik Açılıya eşit veya daha büyük olduğunda, enine dalga kırılma Açısı bir yüzey dalgası oluşturmak için 90'a eşittir).
The transverse wave transmitted along the workpiece surface has a slow speed, low energy and short wavelength, and the detection depth is shallower than the crawling wave. İş parçası yüzeyi boyunca iletilen enine dalga düşük bir hıza, düşük enerjiye ve kısa dalga boyuna sahiptir ve algılama derinliği tarama dalgasından daha sığdır. Therefore, the requirements for the surface finish of the workpiece are stricter than the crawling wave. Bu nedenle, iş parçasının yüzey kalitesi için gereksinimler, tarama dalgasından daha katıdır.
Surface wave detection can only detect defects at a depth of two wavelengths from the surface of the workpiece. Yüzey dalgası tespiti, sadece iş parçasının yüzeyinden iki dalga boyu derinliğinde hataları tespit edebilir. (frequency 2.5mhz wavelength about 1.3mm). (frekans 2.5mhz dalga boyu yaklaşık 1.3mm).